Land Rover Defender Td5 3D-printable parts

Defender door card clip

This is the defender door's sill lock button

Air intake grille. For Defenders equipped with a 300 Tdi, Td5 or Puma motor.

Land Rover Defender Internal Door Handle

Keep snow, ice, and leaves out of your heater intake with this Snow Cowl. The heater intake cover fits Left Hand Drive Defenders (this goes on the Right Hand Wing).

Holds the seatbelt latch so it does not slide down past the shoulder. Universal to any seatbelt of standard width. (3MF file)

Defender wing grills, need drilling.

Plastic bushing fro Land Rover Defender bonnet

This is a defender door's lock button housing

Simple light guards for Land Rover Defender, just attache them with the original screws.

This is a defender door's lock escutcheon

This is a defender's door card clip mount

Land Rover Defender Door Panel Dowel

This is a defender's seat lever knob

Land Rover defender mirror hinge bottom cap

Multi-part dashboard housing, frame, gauge mount, button, adaptor, and support bracket for the BinOwl onboard-computer installation.

Land Rover Defender LT77 Gear knob

Clip Front Seat Belt Retainer For Land Rover Defender

Defender Bonnet Stay Clip, requires a 3mm Allen screw.

Workshop fitting tool for seating the rear hub seal squarely.

Workshop tool for seating the oil seal in an LT230 transfer box. The creator printed it in PETG with a 2 mm shell and 50% infill.

Cubby-box extension with two cup recesses and a central storage pocket.

Adaptor to fit Discovery 2 Cruise Control switch to Defender td5. Quote from SimonRafferty: "It's very easy to add cruise control to any Td5 Land Rover Defender just by adding a couple of wires to the ECU and connecting them to a switch. (search on line for details) Unfortunately, there are no nice looking switches. My solution was to fit a switch from a Td5 Discovery 2 - and print this adaptor so it can easily screw on to the steering column. This is version 2 which is a much better fit and prints in one piece. Use higher temperature filament such as PETG or PAHT - otherwise it will melt in the sun. That's how come V2 came to be! Insert a couple of M4 Nuts into the slots provided, then attach the switch with 2 x M4 x 10mm screws"

Ashtray-slot phone holder for the pre-Puma dashboard.

Clip to hold brake pipes to chassis for Defender TD5. It fits into existing 7mmØ holes in chassis and holds a 5mmØ brake pipe secured by a 4.7mm*1.3mm nylon cable tie. It's designed to be forced into the chassis with a hammer and strongly hold the brake pipe even without beeing secured by the cable tie, but be aware that brake pipes are quite sensible parts of a vehicle and may result to your death if not secured appropriately. Use this part at your own risk and check conditions of the brake pipe clip regularly.

Two headlining fastener sizes for a 110.

This a double fuel pipe clip for Td5 defenders, to hold fuel hoses to the chassis.

Air-intake vent that replaces the removable seat-box floor grommet when fitting a diesel night heater. The creator secured it with marine sealant.

Replacement latch insert for the truck-cab rear sliding window, designed to reuse the original latch housing.

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Clip-in dashboard-vent deflector that directs part of the demister airflow towards the side window. The creator positions it over the vent funnel, about 150 mm from the outer end.

Bezel for installing a 30 mm USB charging outlet in the unused position beside the rear-wiper control on the centre console. The USB outlet clamps the bezel in place.

Replacement flange for repairing or upgrading the Td5 air-filter housing connection.

Push-fit 27 mm wheel-nut cover.

Modular dashboard panel for three rectangular switches, supplied as a one-piece version and a split panel with end cap.

Replacement interior end cap for the roof reinforcement bar.

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Two replacements for the unused 1998 centre-panel opening: a plain plug and a post-mounted version for a small air freshener.

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Cubby-box dock for a cased Samsung Galaxy S5 and a cylindrical Qi charging puck.

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Bracket for mounting a 2016 Elinz FHD dashcam at the passenger sun-visor fixing point, reusing the original visor screw.

Workshop wrench for removing and tightening the fuel-sender retaining ring.

Its an alternative to the front grille screw plastic mounts.