Browse the parts catalogue
Every part on this page has been printed at least once on a real truck. Search by part name, OEM cross-reference, or pick a vehicle generation to narrow it down.
Horn Button Cover
Land Rover Discovery 2 horn button cover.
Rear Window Liner
This is the rear left and right window liner. This requires a larger printer but you can cut it in the slicer and join it afterwards
Wheel-Nut Cover
Push-fit 27 mm wheel-nut cover.
Tow-Cover Thumbwheel Fastener
Tool-free half-turn thumbwheel fastener for the rear towing-point cover. Print at 100% infill for strength.
Speaker-Grille Cover
Replacement speaker-grille cover for the 1998 50th Edition, supplied as one complete piece or two halves for smaller printers.
Fuse Box Cover
Replacement fuse-box cover for the full-size Range Rover Classic.
Rear Seat Row Handle Cover
This 3D-printed seat lever cover is designed as a replacement cover for the seat-folding lever mechanism used for the 6th and 7th passenger seats. It provides a neat, durable solution when the original plastic cover is damaged, missing or worn.
Tow-Hitch Cover Quarter-Turn Clip
Replacement quarter-turn retaining clip for the rear tow-hitch cover.
Three-Door Window-Switch Panel Cover
Replacement cover for the window-switch panel on three-door vehicles. Confirm switch layout and panel dimensions before printing.
Third-Row Seat-Lever Cover
Two-part replacement cover for the third-row seat release lever, with a separate pictogram insert.
Screw-Retained Fuse Cover
Fuse cover designed for an approximately 1993 Range Rover Classic 200Tdi. Uses one M3 x 25 screw. This is the screw-retained alternative to the standard fuse-box cover.
Loadspace-Cover Locating Pin
Two replacement locating-pin variants for the loadspace cover: one for an M8 opening and one for the original 11 × 11 mm square opening. Print horizontally to reduce delamination risk.
Towbar-Cover Screw Retainer
Replacement receiver that grips the quarter-turn plastic screw securing the rear tow-bar cover.
Rear Loadspace-Cover Brackets
Replacement pair for cracked rear loadspace-cover brackets.
Locking Wheel-Nut Cover
Replacement cover for a locking wheel nut.
Tow-Hitch Cover Retaining Clip
Replacement retaining clip for the rear tow-hitch cover and related exterior panels.
Left Power-Seat Switch Cover
Replacement left-hand cover for the power-seat switches on a 1996 vehicle. The ribbed design differs slightly from the original
Terrain-Control Console Cover
Protective cover for the terrain-response and hill-descent-control area of the centre console, intended to prevent pets from pressing the controls accidentally.
Interior Lamp Cover
Interior lamp cover for the full-size Range Rover Classic. Print with supports. Replace the incandescent bulb with an LED before fitting so heat does not deform or melt the printed cover.
Rivet - Plastic Wheel flare
REQ-AFU1075
Multi-purpose plastic snap fastener used to attache the wheel flares
Window Winder Handle Escutcheon
REQ-BTR6620PMA
Chrome or black escutcheon plate that sits behind the manual window winder handle against the door card.
A-Pillar Rain Gutter Finisher (Right)
REQ-DCB500060PMA
Plastic trim piece that covers the A-pillar rain gutter on the right side. One of the most commonly broken Discovery 2 parts. UV degrades the plastic and rivets fail.
A-Pillar Rain Gutter Finisher (Left)
REQ-DCB500070PMA
Plastic trim piece that covers the A-pillar rain gutter on the left side. Same notorious failure as the right side.
Front Bumper End Cap
REQ-LR013413X
Plastic end cap that covers the end of the front bumper. Prevents water and dirt from getting inside the bumper.
24 of 28 shown