Exterior — 3D-printable Land Rover parts

Air intake grille. For Defenders equipped with a 300 Tdi, Td5 or Puma motor.

Keep snow, ice, and leaves out of your heater intake with this Snow Cowl. The heater intake cover fits Left Hand Drive Defenders (this goes on the Right Hand Wing).

Defender wing grills, need drilling.

Plastic bushing fro Land Rover Defender bonnet

Simple light guards for Land Rover Defender, just attache them with the original screws.

Land Rover defender mirror hinge bottom cap

Defender Bonnet Stay Clip, requires a 3mm Allen screw.

Land Rover Discovery 2 bonnet (Hood) prop grommet

Its an alternative to the front grille screw plastic mounts.

Land Rover Discovery 2 fuel door latch.

Front bumper end cap clip for Defender

LandRover Discovery 2 Rear light cover The model provided is for the LEFT side, use the flip/mirror function in your slicer to flip the models for the right side. Can be printed as is, fine details are better. Print in ABS, looks good with some finishing and paint. Helps lights from falling out or getting hit.

Simplified, smaller front bumper corner for the full-size Range Rover Classic 200Tdi. Attaches using the original screw. Confirm side and dimensions against the vehicle before printing.

Replacement socket clip for the headlight adjuster. Two screws secure the clip to the lamp and the socket snaps onto the adjuster ball

Simplified 78 mm centre hub cap for Range Rover Classic alloy wheels. Prints without supports.

Interior lamp cover for the full-size Range Rover Classic. Print with supports. Replace the incandescent bulb with an LED before fitting so heat does not deform or melt the printed cover.

Replacement sunroof rail and locking bracket for the P38 electric sliding roof. Related genuine guide assemblies are EXM100360 (RH) and EXM100370 (LH)

Protective plug for the removable-towbar receiver to keep dirt and debris out when the towbar is removed. Modelled from the original plug.

Multi-part protective plug for the removable-towbar receiver, supplied with two spring sizes for fit adjustment.

Replacement latch component for a broken fuel-filler-door hinge. Compare the model with the original hinge and test movement before final installation.

Replacement trim plug covering the rear-wiper-arm retaining nut. PETG is recommended for sun and heat resistance

Shield that prevents the inner rear parking sensors from detecting a raised aftermarket tow hitch. Print two in ASA or another UV- and heat-resistant material.

Replacement centre cap for a Discovery 3 alloy wheel. Confirm wheel and bore dimensions against the original before printing.

Two-part eyelet mount that clamps around a factory roof rail using common M8 hardware. The source recommends PETG, 20% infill, doubled infill lines, and three walls. Use only for light-duty restraint and never as a rated recovery or lifting point.

Bolt-on adapter for the side-arm front wiper fitting used on 2003–2012 vehicles, converting it to accept a conventional cross-bar blade attachment. Includes editable OpenSCAD source.

Adapter that allows compatible standard 22-inch wiper blades to fit the L322 front wiper arm without additional hardware. The source recommends ABS, three perimeter walls, 40% infill, and supports.

Replacement retaining clip for the plastic wind deflector mounted beneath each front wiper arm on 2002–2012 vehicles. Use a weather- and UV-resistant material.

Protective bung for a factory Westfalia detachable-towbar receiver, intended to keep dirt and moisture out when the hitch is removed. Check receiver dimensions before printing.

Replacement cover for a locking wheel nut.

Push-fit cap for covering an unused roof-rack mounting hole.

Replacement end piece for a longitudinal roof rail.

Replacement plunger for a broken fuel-filler-door actuator.

Replacement cap for the windscreen-washer reservoir.

Replacement plastic control for the Lucas wash/wipe switch. The sacrificial lower support can be removed after printing

Slightly oversized 16 mm bonnet-hinge bush intended to reduce movement and rattling in worn hinge carriers. Print with strong layer bonding and high infill

Three-part replacement socket assembly for an indicator or position lamp using a separate single-contact bulb holder. Verify the 33 mm housing fit, wiring, insulation, and weather sealing.

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Push-fit 27 mm wheel-nut cover.

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Six-piece replacement kit redrawn from surviving original plastic and bakelite wiper-motor components. The positive-terminal insulator uses a simplified M3 through-bolt connection.