Interior — 3D-printable Land Rover parts

Defender door card clip

This is the defender door's sill lock button

Land Rover Defender Internal Door Handle

Holds the seatbelt latch so it does not slide down past the shoulder. Universal to any seatbelt of standard width. (3MF file)

This is a defender door's lock button housing

This is a defender door's lock escutcheon

This is a defender's door card clip mount

Land Rover Defender Door Panel Dowel

Land Rover Discovery 2 window and heating switch cover. You need to print 4 pins.

This is a defender's seat lever knob

A cup holder that clips to the metal dash of a Series 1-2a.

Multi-part dashboard housing, frame, gauge mount, button, adaptor, and support bracket for the BinOwl onboard-computer installation.

Land Rover Defender LT77 Gear knob

Clip Front Seat Belt Retainer For Land Rover Defender

Originally built to mount a Bolt&Trim Leather speaker holder for the Marshall speaker. This allows for a temporary/movable mount based originally on a cup holder. Could be easily modified for other speaker styles.

Land Rover Discovery 2 horn button cover.

Land Rover Discovery 3 armrest cap.

Cubby-box extension with two cup recesses and a central storage pocket.

Adaptor to fit Discovery 2 Cruise Control switch to Defender td5. Quote from SimonRafferty: "It's very easy to add cruise control to any Td5 Land Rover Defender just by adding a couple of wires to the ECU and connecting them to a switch. (search on line for details) Unfortunately, there are no nice looking switches. My solution was to fit a switch from a Td5 Discovery 2 - and print this adaptor so it can easily screw on to the steering column. This is version 2 which is a much better fit and prints in one piece. Use higher temperature filament such as PETG or PAHT - otherwise it will melt in the sun. That's how come V2 came to be! Insert a couple of M4 Nuts into the slots provided, then attach the switch with 2 x M4 x 10mm screws"

Ashtray-slot phone holder for the pre-Puma dashboard.

Trim Clip for Fuse Box Cover on Defender from 2007 Onwards

Land Rover Discovery 1/2 window switch bezel. You need to print 4 pins

Repair clip for a broken rear-seat latch, supplied with a trim-removal tool. Reuses the original spring

Tool-free half-turn thumbwheel fastener for the rear towing-point cover. Print at 100% infill for strength.

Two headlining fastener sizes for a 110.

Repair set for later window-regulator motor assemblies, including gear-coupler and roller options. Some versions require drilling and tapping the original steel hub or roller shaft

This is replacement of original LR handle for folding of 3rd row seats in Discovery 2 models.

Replacement fuse-box cover for the full-size Range Rover Classic.

Fuse cover designed for an approximately 1993 Range Rover Classic 200Tdi. Uses one M3 x 25 screw. This is the screw-retained alternative to the standard fuse-box cover.

Dashboard blanking plate for a full-size Range Rover Classic when no car radio is installed.

Simplified fixed replica of the original Range Rover Classic dashboard vent grille. The source model is based on a full-size Classic and is intended to be glued in place.

Replacement clips for the Range Rover Classic plastic access-panel doors beneath the front seats. Includes a friction-fit version and a version with a retaining lip. Attach with a small Command strip or glue

Replacement protective sleeve for the Range Rover Classic heated rear-window cables, Land Rover part 589818. The source author changed the original round section to a square section and tuned the curvature for fit. PETG or nylon is preferable to brittle PLA. LR3DParts converted the original ASCII STL to binary STL without changing its geometry for upload compatibility.

Custom replacement for the front ashtray section of a 1999 Range Rover P38 4.0 automatic. Includes a standard cigarette-lighter socket opening, space for additional switches, a 2 mm smaller version for vinyl covering, and separate mounting brackets for printers with smaller beds. The related 1999 front centre-console ashtray assembly is Land Rover FKH100350

Replacement door-panel/card retainer stud for the Range Rover P38 and Discovery 2. Corresponds to genuine Land Rover MWC9134

Dashboard drinks holder for the Range Rover P38, based on genuine Land Rover accessory LRN32685 with printability changes and an added tray for pens and coins.

Custom panel for a Range Rover P38 stock radio slot, holding auxiliary switches, the ride-height switch, and the interior-air-temperature sensor after relocating the original radio. This is a community accessory with no Land Rover Genuine part number. The source recommends printing the front panel flat on the bed at about 20% infill without supports.

Top half of the twist-lock clip for P38 rubber floor mats. The upper retainer has no confirmed standalone Land Rover part number. Use ABS rather than brittle PLA. Converted the original ASCII STL to binary without changing its geometry for upload compatibility.

Printable button, collar, and stop components for exposing the unused steering-wheel control switches found beneath some SE trim covers. Cruise-control activation may require diagnostic coding.

Replacement nozzle for the cabin air duct, supplied in screw-in and long-thread versions for differently damaged mounting holes. The source recommends printing upright in PETG.

Two-piece radio surround and mounting bracket designed for a flush Pioneer double-DIN installation

Headrest-mounted holder for a BaoFeng UV-5R handheld radio, with standard- and extended-battery options plus a screw-retained crossbar. PETG is recommended for cabin heat resistance.

Two-part replacement cover for the third-row seat release lever, with a separate pictogram insert.

Multi-part eight-inch tablet holder designed for the Discovery 3 cabin. Includes the mount, articulated ball-head components, spring, insert, cable guide, nut, and assembly model.

Protective cover for the terrain-response and hill-descent-control area of the centre console, intended to prevent pets from pressing the controls accidentally.

Replacement console cup-holder bodies with flexible retaining stays. Print the main body in PETG and the stays in TPU, then press the stays in from the outside before installation.

Two-part dashboard phone mount designed around a compact Qi charging puck. Attaches with double-sided foam tape and includes left- and right-side mounting options by mirroring

Small friction-fit repair piece that restores the lower passenger cup-holder hinge after its moulded pins shear off. Print two

Two-part bracket and frame for installing Carling-style accessory switches in place of the factory ashtray.

Four-part holder for installing a Webasto MultiControl unit in place of the factory ashtray, including base, bracket, front panel, and spring clip.

Dashboard auxiliary-power panel supplied as a single-piece model, with the source also describing a two-piece option for smaller print beds. Confirm socket and switch dimensions before assembly.

Removable Garmin Nuvi mount sized to sit over the factory navigation display. A raised upper lip locates it in the recess

Holder that keeps a second-row seat-belt buckle upright so children can buckle themselves more easily. Designed around the Discovery mid-row seat geometry.

Replacement adjuster for the rear seat. Includes the original version and a revised version that prints without supports

Replacement toggle that retains the rear towing-connection flap. Print at 100% infill

Replacement quarter-turn screw for retaining the rear-bumper towbar access door when the towbar is not fitted. Print with high infill and confirm engagement before road use.

Insert for the centre-console cubby refrigerator in a 2007 Discovery 3, designed to keep drink cans from rolling and vibrating while driving. Use a cabin-temperature-resistant material.

Dashboard phone mount for fitting a Quad Lock interface in the Discovery 3/LR3 cabin. Confirm the mating interface and dashboard fit before final installation.

Dashboard bracket for a 9.3-inch portable CarPlay display. The upper edge tucks beneath the dashboard trim while taped feet support the screen

Replacement captive clip for securing a number-plate screw when the original body clip is missing. The source recommends cutting the screw thread before installing the clip and using a tougher material than PLA.

Replacement push clip for the front cowl and wiper-panel cover on 2002–2009 vehicles. Use a flexible, weather-resistant material and compare dimensions with an original clip before fitting.

Two-part holder and lid for mounting a Nexus 9 tablet in a 2002–2012 dashboard installation, suitable for an Android Auto client or other tablet-based interface. Editable OpenSCAD sources are included.

Phone holder designed to sit in the front coin tray, sized around an iPhone 11 in an Apple case. Confirm phone and tray dimensions before printing and use a heat-resistant cabin material.

Replacement internal bar for a broken cabin heater and air-conditioning vent grille. Confirm vent position and dimensions against the original before printing.

Replacement push-fit stud used between the passenger and rear door cards and the plastic receivers in the door structure. Multiple clips are used per panel

Replacement cover for the window-switch panel on three-door vehicles. Confirm switch layout and panel dimensions before printing.

Reinforced replacement bracket for a broken rear parcel shelf. Compare side and mounting geometry with the original before printing.

Replacement left-hand cover for the power-seat switches on a 1996 vehicle. The ribbed design differs slightly from the original

Bolt-on repair pieces for parcel-shelf eyelets that have torn through. Requires trimming the shelf and two M3 x 7 mm fasteners

Replacement for the rear ashtray that accepts a standard cigarette-lighter or USB power socket. Use a cabin-temperature-resistant material and verify socket dimensions.

Dashboard surround for fitting a protruding double-DIN navigation head unit without cutting the original dash trim. PETG is recommended because PLA can deform in a hot cabin.

Two-part centre-console cup holder with an enlarged approximately 75 mm internal diameter and no phone pocket. Designed from a related holder and explicitly stated to fit this generation.

Multi-part dashboard tray replacement with interchangeable faces for USB, a brake-controller dial, or three Carling-style switches. Glue the selected face to the tray after test-fitting.

Three-part replacement sun-visor retainer for either side. Print the body flat, the clip prongs upward, and the cap with its tube upward, then glue the clip into the body before installation.

Replacement blanking button for an unused dashboard switch position. Two model variants are included

Angled roof-console pod for two 52 mm gauges. Installation requires trimming part of the original mating flange and securing the pod with small countersunk screws.

Dashboard cradle sized for an iPhone X and designed around the 2012 cabin layout.

Replacement retaining clip for the rear tow-hitch cover and related exterior panels.

Four-part fascia, side-bracket, and brace set for installing an aftermarket double-DIN stereo in the 2008 dashboard.

Replacement driven gear for a window-regulator motor mechanism.

Replacement threaded carpet retainer.

No-drill rear-camera holder that replaces one number-plate-light position. Confirm camera dimensions, cable routing, and local lighting requirements before installation.

Four-part clamp mount for attaching a Salora CDC100-style dashcam to the interior mirror. Short and tall ball-arm options are included, together with the mirror clamp and retaining nut.

Replacement end cap for the passenger roof grab handle, measured from a 2000 four-door vehicle.

Two-piece fixing for securing the loadspace carpet.

Replacement pair for cracked rear loadspace-cover brackets.

Three alternative inserts for an ashtray or coin-tray opening: a blank panel, a three-switch panel, and a dual socket panel.

Replacement receiver that grips the quarter-turn plastic screw securing the rear tow-bar cover.

Two-part centre-console organiser comprising a main tray and removable divider. Use a cabin-temperature-resistant material because PLA may soften in summer heat.

Two replacement locating-pin variants for the loadspace cover: one for an M8 opening and one for the original 11 × 11 mm square opening. Print horizontally to reduce delamination risk.

Flexible replacement overlay for worn key-fob buttons. Two versions are included: a partial overlay and a full button-hole overlay. Print in a flexible material with a fine nozzle.

Replacement quarter-turn retaining clip for the rear tow-hitch cover.

Two-piece coin organiser for the centre-console area, comprising a main holder and lid.

Two-piece overlay repair for a broken glovebox-damper attachment. The body clips over the damaged damper and a half-ring lock provides additional retention.

Replacement internal gear set for a failed tailgate-lock actuator. Three printable variants are included

Bolt-on lower clip and rotating sleeve for repairing the glovebox damper. Install with an M3 × 16 mm fastener, nut, and locking washer, and orient the clip for strength as shown by the source.

Deep dashboard-console mount for integrating a seven-inch tablet. Installation requires electrical adaptation and modification of the tablet controls

Three-part loadspace-light conversion comprising an installation template, switch panel, and blanking plate. Wiring polarity and switching differ between early and later vehicles, so verify the circuit before modification.

Replacement lower-dashboard air vent in the later flat style.

Modular dashboard base with two M6 attachment points, plus compatible Garmin and Motorola device holders. The base attaches to the vinyl dashboard with automotive-grade double-sided tape.

Replacement COLD–WARM heater control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Replacement threaded button for the handbrake lever. The source recommends finishing the undersized bore with an M5 tap for a secure fit.

Replacement support bracket for the instrument cluster where the original is missing or damaged. Compare handedness, hole spacing, and dashboard structure before printing.

Left- and right-hand enclosures for 100 mm speakers up to approximately 48 mm deep. Mirrored and split-file variants are included

Simple cab hook for retaining a loose seat belt when it is not in use. Confirm the mounting position and belt clearance before drilling or attaching it.

Replacement UP–DOWN heater airflow control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Replacement lettered knob for a missing bulkhead-vent control. It is designed to be heat-pressed onto the original mechanism

Base-plate adapter for fitting GMC/Chevrolet pickup tie-down anchors to the cargo-area ceiling. Installation uses two 3/8 × 1.5-inch carriage bolts with washers and nuts.

Console for mounting auxiliary switches or other equipment in the small driver-side dashboard recess. Blank and pre-drilled versions are included for both left- and right-hand-drive vehicles

Air-intake vent that replaces the removable seat-box floor grommet when fitting a diesel night heater. The creator secured it with marine sealant.

Five-piece double-DIN stereo binnacle for the pre-Td5 dashboard. Assembly uses twelve M4 countersunk bolts and twelve M4 nuts.

Replacement latch insert for the truck-cab rear sliding window, designed to reuse the original latch housing.

Clip-in dashboard-vent deflector that directs part of the demister airflow towards the side window. The creator positions it over the vent funnel, about 150 mm from the outer end.

Bezel for installing a 30 mm USB charging outlet in the unused position beside the rear-wiper control on the centre console. The USB outlet clamps the bezel in place.

Three panel variants for combining switches and a voltmeter, designed for the 200 Tdi dashboard.

Dashboard holder for mounting a compact CB radio in the Puma interior.

Two-part dashboard hanger and extension for an Anker Soundcore Motion Boom portable speaker.

Two dashboard vent inserts that redirect cabin airflow.

Dashboard mounting bracket for a Garmin navigation unit in the Puma interior.

Modular dashboard panel for three rectangular switches, supplied as a one-piece version and a split panel with end cap.

Replacement interior end cap for the roof reinforcement bar.

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Two replacements for the unused 1998 centre-panel opening: a plain plug and a post-mounted version for a small air freshener.

Cubby-box dock for a cased Samsung Galaxy S5 and a cylindrical Qi charging puck.

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Bracket for mounting a 2016 Elinz FHD dashcam at the passenger sun-visor fixing point, reusing the original visor screw.

Replacement speaker-grille cover for the 1998 50th Edition, supplied as one complete piece or two halves for smaller printers.

Replacement ventilator control knob modelled from the original component.

Three-piece 12-volt inspection-lamp socket adaptation using standard 4 mm RC bullet connectors, 14 AWG silicone wire, and an M3 x 12 mm fastener.

Door-hinge packing shims in three thicknesses. They also separate dissimilar metals to help reduce electrolytic corrosion

Loose- and tight-fit holders for fitting a 5 mm 12-volt LED and panel-mount bezel into a 16 mm Jaeger or Smiths gauge opening. The creator notes that the tight version may break during removal and suggests optional hot glue after installing the LED.

Bulkhead-mounted holder for a standard 33 cl can, with a recess for an optional 6 mm retaining magnet.