Interior — 3D-printable Land Rover parts

Ashtray-slot phone holder for the pre-Puma dashboard.

Land Rover Discovery 2 window and heating switch cover. You need to print 4 pins.

A cup holder that clips to the metal dash of a Series 1-2a.

Land Rover Defender LT77 Gear knob

Land Rover Discovery 2 horn button cover.

Dashboard mounting bracket for a Garmin navigation unit in the Puma interior.

Two-part bracket and frame for installing Carling-style accessory switches in place of the factory ashtray.

Multi-part dashboard housing, frame, gauge mount, button, adaptor, and support bracket for the BinOwl onboard-computer installation.

Replacement blanking button for an unused dashboard switch position. Two model variants are included

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Clip-in dashboard-vent deflector that directs part of the demister airflow towards the side window. The creator positions it over the vent funnel, about 150 mm from the outer end.

Inner center-console bracket for the Land Rover Discovery 2 switch bank. It supports four window switches, two heated-seat switches, and the rear-window lockout switch, and is intended for the fully populated seven-switch console layout.

Land Rover Discovery 1/2 window switch bezel. You need to print 4 pins

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Custom panel for a Range Rover P38 stock radio slot, holding auxiliary switches, the ride-height switch, and the interior-air-temperature sensor after relocating the original radio. This is a community accessory with no Land Rover Genuine part number. The source recommends printing the front panel flat on the bed at about 20% infill without supports.

Replacement ventilator control knob modelled from the original component.

Dashboard bracket for a 9.3-inch portable CarPlay display. The upper edge tucks beneath the dashboard trim while taped feet support the screen

Originally built to mount a Bolt&Trim Leather speaker holder for the Marshall speaker. This allows for a temporary/movable mount based originally on a cup holder. Could be easily modified for other speaker styles.

Adaptor to fit Discovery 2 Cruise Control switch to Defender td5. Quote from SimonRafferty: "It's very easy to add cruise control to any Td5 Land Rover Defender just by adding a couple of wires to the ECU and connecting them to a switch. (search on line for details) Unfortunately, there are no nice looking switches. My solution was to fit a switch from a Td5 Discovery 2 - and print this adaptor so it can easily screw on to the steering column. This is version 2 which is a much better fit and prints in one piece. Use higher temperature filament such as PETG or PAHT - otherwise it will melt in the sun. That's how come V2 came to be! Insert a couple of M4 Nuts into the slots provided, then attach the switch with 2 x M4 x 10mm screws"

Four-piece replacement repair set for the air-conditioning louvre assembly in a 1995 Land Rover Defender 300 Tdi (1994-1998), comprising the louvre, outer frame, alignment strip, and louvre clip rail. The louvre-fit holes require drilling to 2.5 mm; the louvre requires supports and the other components print without supports. Verify the exact AC vent variant, hole size, retention, louvre movement, and cabin-heat material suitability before installation. This should also fit other pre-puma/td4 Defenders

Multi-part dashboard tray replacement with interchangeable faces for USB, a brake-controller dial, or three Carling-style switches. Glue the selected face to the tray after test-fitting.

Two-piece radio surround and mounting bracket designed for a flush Pioneer double-DIN installation

Simplified fixed replica of the original Range Rover Classic dashboard vent grille. The source model is based on a full-size Classic and is intended to be glued in place.

Five-piece double-DIN stereo binnacle for the pre-Td5 dashboard. Assembly uses twelve M4 countersunk bolts and twelve M4 nuts.