@Razzmatazz

Replacement fuse-box cover for the full-size Range Rover Classic.

Fuse cover designed for an approximately 1993 Range Rover Classic 200Tdi. Uses one M3 x 25 screw. This is the screw-retained alternative to the standard fuse-box cover.

Dashboard blanking plate for a full-size Range Rover Classic when no car radio is installed.

Simplified 78 mm centre hub cap for Range Rover Classic alloy wheels. Prints without supports.

Interior lamp cover for the full-size Range Rover Classic. Print with supports. Replace the incandescent bulb with an LED before fitting so heat does not deform or melt the printed cover.

Simplified fixed replica of the original Range Rover Classic dashboard vent grille. The source model is based on a full-size Classic and is intended to be glued in place.

Simplified, smaller front bumper corner for the full-size Range Rover Classic 200Tdi. Attaches using the original screw. Confirm side and dimensions against the vehicle before printing.

Replacement clips for the Range Rover Classic plastic access-panel doors beneath the front seats. Includes a friction-fit version and a version with a retaining lip. Attach with a small Command strip or glue

Replacement protective sleeve for the Range Rover Classic heated rear-window cables, Land Rover part 589818. The source author changed the original round section to a square section and tuned the curvature for fit. PETG or nylon is preferable to brittle PLA. LR3DParts converted the original ASCII STL to binary STL without changing its geometry for upload compatibility.

Height-setting blocks for calibrating Range Rover P38 electronic air suspension level sensors. Includes front and rear blocks for Access, Low, Standard, and High settings

Custom replacement for the front ashtray section of a 1999 Range Rover P38 4.0 automatic. Includes a standard cigarette-lighter socket opening, space for additional switches, a 2 mm smaller version for vinyl covering, and separate mounting brackets for printers with smaller beds. The related 1999 front centre-console ashtray assembly is Land Rover FKH100350

Reinforced replacement bonnet-release lever for a right-hand-drive Range Rover P38. Corresponds to Land Rover FSC10004

Replacement door-panel/card retainer stud for the Range Rover P38 and Discovery 2. Corresponds to genuine Land Rover MWC9134

Dashboard drinks holder for the Range Rover P38, based on genuine Land Rover accessory LRN32685 with printability changes and an added tray for pens and coins.

Custom panel for a Range Rover P38 stock radio slot, holding auxiliary switches, the ride-height switch, and the interior-air-temperature sensor after relocating the original radio. This is a community accessory with no Land Rover Genuine part number. The source recommends printing the front panel flat on the bed at about 20% infill without supports.

Replacement sunroof rail and locking bracket for the P38 electric sliding roof. Related genuine guide assemblies are EXM100360 (RH) and EXM100370 (LH)

Top half of the twist-lock clip for P38 rubber floor mats. The upper retainer has no confirmed standalone Land Rover part number. Use ABS rather than brittle PLA. Converted the original ASCII STL to binary without changing its geometry for upload compatibility.

Printable button, collar, and stop components for exposing the unused steering-wheel control switches found beneath some SE trim covers. Cruise-control activation may require diagnostic coding.

Replacement nozzle for the cabin air duct, supplied in screw-in and long-thread versions for differently damaged mounting holes. The source recommends printing upright in PETG.

Protective plug for the removable-towbar receiver to keep dirt and debris out when the towbar is removed. Modelled from the original plug.

Two-piece radio surround and mounting bracket designed for a flush Pioneer double-DIN installation

Headrest-mounted holder for a BaoFeng UV-5R handheld radio, with standard- and extended-battery options plus a screw-retained crossbar. PETG is recommended for cabin heat resistance.

Two-part replacement cover for the third-row seat release lever, with a separate pictogram insert.

Protective cover for the terrain-response and hill-descent-control area of the centre console, intended to prevent pets from pressing the controls accidentally.

Repair clip for a broken rear-seat latch, supplied with a trim-removal tool. Reuses the original spring

Replacement console cup-holder bodies with flexible retaining stays. Print the main body in PETG and the stays in TPU, then press the stays in from the outside before installation.

Two-part dashboard phone mount designed around a compact Qi charging puck. Attaches with double-sided foam tape and includes left- and right-side mounting options by mirroring

Replacement latch component for a broken fuel-filler-door hinge. Compare the model with the original hinge and test movement before final installation.

Small friction-fit repair piece that restores the lower passenger cup-holder hinge after its moulded pins shear off. Print two

Two-part bracket and frame for installing Carling-style accessory switches in place of the factory ashtray.

Four-part holder for installing a Webasto MultiControl unit in place of the factory ashtray, including base, bracket, front panel, and spring clip.

Replacement trim plug covering the rear-wiper-arm retaining nut. PETG is recommended for sun and heat resistance

Shield that prevents the inner rear parking sensors from detecting a raised aftermarket tow hitch. Print two in ASA or another UV- and heat-resistant material.

Tool-free half-turn thumbwheel fastener for the rear towing-point cover. Print at 100% infill for strength.

Removable Garmin Nuvi mount sized to sit over the factory navigation display. A raised upper lip locates it in the recess

Holder that keeps a second-row seat-belt buckle upright so children can buckle themselves more easily. Designed around the Discovery mid-row seat geometry.

Replacement centre cap for a Discovery 3 alloy wheel. Confirm wheel and bore dimensions against the original before printing.

Replacement adjuster for the rear seat. Includes the original version and a revised version that prints without supports

Replacement toggle that retains the rear towing-connection flap. Print at 100% infill

Replacement quarter-turn screw for retaining the rear-bumper towbar access door when the towbar is not fitted. Print with high infill and confirm engagement before road use.

Two-part eyelet mount that clamps around a factory roof rail using common M8 hardware. The source recommends PETG, 20% infill, doubled infill lines, and three walls. Use only for light-duty restraint and never as a rated recovery or lifting point.

Insert for the centre-console cubby refrigerator in a 2007 Discovery 3, designed to keep drink cans from rolling and vibrating while driving. Use a cabin-temperature-resistant material.

Dashboard phone mount for fitting a Quad Lock interface in the Discovery 3/LR3 cabin. Confirm the mating interface and dashboard fit before final installation.

Dashboard bracket for a 9.3-inch portable CarPlay display. The upper edge tucks beneath the dashboard trim while taped feet support the screen

Replacement captive clip for securing a number-plate screw when the original body clip is missing. The source recommends cutting the screw thread before installing the clip and using a tougher material than PLA.

Bolt-on adapter for the side-arm front wiper fitting used on 2003–2012 vehicles, converting it to accept a conventional cross-bar blade attachment. Includes editable OpenSCAD source.

Replacement push clip for the front cowl and wiper-panel cover on 2002–2009 vehicles. Use a flexible, weather-resistant material and compare dimensions with an original clip before fitting.

Adapter that allows compatible standard 22-inch wiper blades to fit the L322 front wiper arm without additional hardware. The source recommends ABS, three perimeter walls, 40% infill, and supports.

Replacement retaining clip for the plastic wind deflector mounted beneath each front wiper arm on 2002–2012 vehicles. Use a weather- and UV-resistant material.

Two-part holder and lid for mounting a Nexus 9 tablet in a 2002–2012 dashboard installation, suitable for an Android Auto client or other tablet-based interface. Editable OpenSCAD sources are included.

Phone holder designed to sit in the front coin tray, sized around an iPhone 11 in an Apple case. Confirm phone and tray dimensions before printing and use a heat-resistant cabin material.

Replacement internal bar for a broken cabin heater and air-conditioning vent grille. Confirm vent position and dimensions against the original before printing.

Protective bung for a factory Westfalia detachable-towbar receiver, intended to keep dirt and moisture out when the hitch is removed. Check receiver dimensions before printing.

Replacement socket clip for the headlight adjuster. Two screws secure the clip to the lamp and the socket snaps onto the adjuster ball

Replacement push-fit stud used between the passenger and rear door cards and the plastic receivers in the door structure. Multiple clips are used per panel

Replacement cover for the window-switch panel on three-door vehicles. Confirm switch layout and panel dimensions before printing.

Reinforced replacement bracket for a broken rear parcel shelf. Compare side and mounting geometry with the original before printing.

Replacement left-hand cover for the power-seat switches on a 1996 vehicle. The ribbed design differs slightly from the original

Bolt-on repair pieces for parcel-shelf eyelets that have torn through. Requires trimming the shelf and two M3 x 7 mm fasteners

Replacement for the rear ashtray that accepts a standard cigarette-lighter or USB power socket. Use a cabin-temperature-resistant material and verify socket dimensions.

Dashboard surround for fitting a protruding double-DIN navigation head unit without cutting the original dash trim. PETG is recommended because PLA can deform in a hot cabin.

Two-part centre-console cup holder with an enlarged approximately 75 mm internal diameter and no phone pocket. Designed from a related holder and explicitly stated to fit this generation.

Multi-part dashboard tray replacement with interchangeable faces for USB, a brake-controller dial, or three Carling-style switches. Glue the selected face to the tray after test-fitting.

Repair set for later window-regulator motor assemblies, including gear-coupler and roller options. Some versions require drilling and tapping the original steel hub or roller shaft

Three-part replacement sun-visor retainer for either side. Print the body flat, the clip prongs upward, and the cap with its tube upward, then glue the clip into the body before installation.

Replacement blanking button for an unused dashboard switch position. Two model variants are included

Angled roof-console pod for two 52 mm gauges. Installation requires trimming part of the original mating flange and securing the pod with small countersunk screws.

Dashboard cradle sized for an iPhone X and designed around the 2012 cabin layout.

Replacement retaining clip for the rear tow-hitch cover and related exterior panels.

Replacement air intake for a Webasto Thermo Top V fuel-burning heater when the original retaining legs have broken. Print with the legs downward and supports from the build plate.

Four-part fascia, side-bracket, and brace set for installing an aftermarket double-DIN stereo in the 2008 dashboard.

Replacement cover for a locking wheel nut.

Replacement driven gear for a window-regulator motor mechanism.

Replacement threaded carpet retainer.

Replacement bushing for the manual gear linkage above the gearbox, intended to reduce excess movement during gear selection. Use a durable, wear-resistant material and verify the linkage joint before fitting.

No-drill rear-camera holder that replaces one number-plate-light position. Confirm camera dimensions, cable routing, and local lighting requirements before installation.

Four-part clamp mount for attaching a Salora CDC100-style dashcam to the interior mirror. Short and tall ball-arm options are included, together with the mirror clamp and retaining nut.

Press sleeve for fitting a support bearing onto the viscous-coupling unit while loading the bearing inner race.

Replacement end cap for the passenger roof grab handle, measured from a 2000 four-door vehicle.

Two-piece fixing for securing the loadspace carpet.

Replacement pair for cracked rear loadspace-cover brackets.

Three alternative inserts for an ashtray or coin-tray opening: a blank panel, a three-switch panel, and a dual socket panel.

Workshop fitting tool for seating the rear hub seal squarely.

Wheel-centre reference tool that holds a tape measure at the true hub centre during suspension-height calibration.

Replacement receiver that grips the quarter-turn plastic screw securing the rear tow-bar cover.

Two-part centre-console organiser comprising a main tray and removable divider. Use a cabin-temperature-resistant material because PLA may soften in summer heat.

Push-fit cap for covering an unused roof-rack mounting hole.

Replacement end piece for a longitudinal roof rail.

Two replacement locating-pin variants for the loadspace cover: one for an M8 opening and one for the original 11 × 11 mm square opening. Print horizontally to reduce delamination risk.

Replacement quarter-turn retaining clip for the rear tow-hitch cover.

Replacement plunger for a broken fuel-filler-door actuator.

Two-piece coin organiser for the centre-console area, comprising a main holder and lid.

Two-piece overlay repair for a broken glovebox-damper attachment. The body clips over the damaged damper and a half-ring lock provides additional retention.

Replacement cap for the windscreen-washer reservoir.

Support ring fitted beneath the fuel-cap thread seal to improve compression and help prevent evaporative-system leaks.

Replacement internal gear set for a failed tailgate-lock actuator. Three printable variants are included

Bolt-on lower clip and rotating sleeve for repairing the glovebox damper. Install with an M3 × 16 mm fastener, nut, and locking washer, and orient the clip for strength as shown by the source.

Multi-part workshop tool for removing and installing the cabin blower motor. It requires M5 threaded rod, nuts, bolts, and bonded inserts

Deep dashboard-console mount for integrating a seven-inch tablet. Installation requires electrical adaptation and modification of the tablet controls

Three-part loadspace-light conversion comprising an installation template, switch panel, and blanking plate. Wiring polarity and switching differ between early and later vehicles, so verify the circuit before modification.

Replacement bush used with a standard 5/16-inch bolt and locking nut to align the brake shoes. Tap the printed bore to suit the bolt thread and follow the source adjustment method.

Replacement plastic control for the Lucas wash/wipe switch. The sacrificial lower support can be removed after printing

Replacement lower-dashboard air vent in the later flat style.

Modular dashboard base with two M6 attachment points, plus compatible Garmin and Motorola device holders. The base attaches to the vinyl dashboard with automotive-grade double-sided tape.

Replacement COLD–WARM heater control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Replacement threaded button for the handbrake lever. The source recommends finishing the undersized bore with an M5 tap for a secure fit.

Slightly oversized 16 mm bonnet-hinge bush intended to reduce movement and rattling in worn hinge carriers. Print with strong layer bonding and high infill

Replacement support bracket for the instrument cluster where the original is missing or damaged. Compare handedness, hole spacing, and dashboard structure before printing.

Left- and right-hand enclosures for 100 mm speakers up to approximately 48 mm deep. Mirrored and split-file variants are included

Workshop mandrel for centring the clutch plate during assembly. Confirm the spigot and spline diameters against the gearbox input shaft and clutch before use.

Simple cab hook for retaining a loose seat belt when it is not in use. Confirm the mounting position and belt clearance before drilling or attaching it.

Temporary reservoir cap for pressure-assisted brake bleeding. Inspect the print, seal, and hose connection carefully and use only low, controlled pressure.

Three-part replacement socket assembly for an indicator or position lamp using a separate single-contact bulb holder. Verify the 33 mm housing fit, wiring, insulation, and weather sealing.

Replacement UP–DOWN heater airflow control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Replacement lettered knob for a missing bulkhead-vent control. It is designed to be heat-pressed onto the original mechanism

Base-plate adapter for fitting GMC/Chevrolet pickup tie-down anchors to the cargo-area ceiling. Installation uses two 3/8 × 1.5-inch carriage bolts with washers and nuts.

Console for mounting auxiliary switches or other equipment in the small driver-side dashboard recess. Blank and pre-drilled versions are included for both left- and right-hand-drive vehicles

Air-intake vent that replaces the removable seat-box floor grommet when fitting a diesel night heater. The creator secured it with marine sealant.

Five-piece double-DIN stereo binnacle for the pre-Td5 dashboard. Assembly uses twelve M4 countersunk bolts and twelve M4 nuts.

Replacement latch insert for the truck-cab rear sliding window, designed to reuse the original latch housing.

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Clip-in dashboard-vent deflector that directs part of the demister airflow towards the side window. The creator positions it over the vent funnel, about 150 mm from the outer end.

Bezel for installing a 30 mm USB charging outlet in the unused position beside the rear-wiper control on the centre console. The USB outlet clamps the bezel in place.

Two headlining fastener sizes for a 110.

Three panel variants for combining switches and a voltmeter, designed for the 200 Tdi dashboard.

Dashboard holder for mounting a compact CB radio in the Puma interior.

Replacement flange for repairing or upgrading the Td5 air-filter housing connection.

Push-fit 27 mm wheel-nut cover.

Two-part dashboard hanger and extension for an Anker Soundcore Motion Boom portable speaker.

Two dashboard vent inserts that redirect cabin airflow.

Dashboard mounting bracket for a Garmin navigation unit in the Puma interior.

Modular dashboard panel for three rectangular switches, supplied as a one-piece version and a split panel with end cap.

Replacement interior end cap for the roof reinforcement bar.

Multi-part dashboard housing, frame, gauge mount, button, adaptor, and support bracket for the BinOwl onboard-computer installation.

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Three-piece adaptor set for fitting a 1995 Ford F-150 throttle-position sensor to a 1994 3.9-litre V8 throttle body. The creator specifies PETG for engine-bay heat resistance.

Two replacements for the unused 1998 centre-panel opening: a plain plug and a post-mounted version for a small air freshener.

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Ashtray-slot phone holder for the pre-Puma dashboard.

Cubby-box dock for a cased Samsung Galaxy S5 and a cylindrical Qi charging puck.

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Bracket for mounting a 2016 Elinz FHD dashcam at the passenger sun-visor fixing point, reusing the original visor screw.

Workshop wrench for removing and tightening the fuel-sender retaining ring.

Workshop tool for seating the oil seal in an LT230 transfer box. The creator printed it in PETG with a 2 mm shell and 50% infill.

Cubby-box extension with two cup recesses and a central storage pocket.

Replacement speaker-grille cover for the 1998 50th Edition, supplied as one complete piece or two halves for smaller printers.

Workshop tool for installing the front crankshaft seal on 2.2- and 2.4-litre Puma engines.