Land Rover Discovery 3 3D-printable parts

Holds the seatbelt latch so it does not slide down past the shoulder. Universal to any seatbelt of standard width. (3MF file)

Land Rover Discovery 3 armrest cap.

Repair clip for a broken rear-seat latch, supplied with a trim-removal tool. Reuses the original spring

Tool-free half-turn thumbwheel fastener for the rear towing-point cover. Print at 100% infill for strength.

Printable button, collar, and stop components for exposing the unused steering-wheel control switches found beneath some SE trim covers. Cruise-control activation may require diagnostic coding.

Replacement nozzle for the cabin air duct, supplied in screw-in and long-thread versions for differently damaged mounting holes. The source recommends printing upright in PETG.

Protective plug for the removable-towbar receiver to keep dirt and debris out when the towbar is removed. Modelled from the original plug.

Two-piece radio surround and mounting bracket designed for a flush Pioneer double-DIN installation

Headrest-mounted holder for a BaoFeng UV-5R handheld radio, with standard- and extended-battery options plus a screw-retained crossbar. PETG is recommended for cabin heat resistance.

Multi-part protective plug for the removable-towbar receiver, supplied with two spring sizes for fit adjustment.

Two-part replacement cover for the third-row seat release lever, with a separate pictogram insert.

Multi-part eight-inch tablet holder designed for the Discovery 3 cabin. Includes the mount, articulated ball-head components, spring, insert, cable guide, nut, and assembly model.

Protective cover for the terrain-response and hill-descent-control area of the centre console, intended to prevent pets from pressing the controls accidentally.

Replacement console cup-holder bodies with flexible retaining stays. Print the main body in PETG and the stays in TPU, then press the stays in from the outside before installation.

Two-part dashboard phone mount designed around a compact Qi charging puck. Attaches with double-sided foam tape and includes left- and right-side mounting options by mirroring

Replacement latch component for a broken fuel-filler-door hinge. Compare the model with the original hinge and test movement before final installation.

Small friction-fit repair piece that restores the lower passenger cup-holder hinge after its moulded pins shear off. Print two

Two-part bracket and frame for installing Carling-style accessory switches in place of the factory ashtray.

Four-part holder for installing a Webasto MultiControl unit in place of the factory ashtray, including base, bracket, front panel, and spring clip.

Replacement trim plug covering the rear-wiper-arm retaining nut. PETG is recommended for sun and heat resistance

Dashboard auxiliary-power panel supplied as a single-piece model, with the source also describing a two-piece option for smaller print beds. Confirm socket and switch dimensions before assembly.

Shield that prevents the inner rear parking sensors from detecting a raised aftermarket tow hitch. Print two in ASA or another UV- and heat-resistant material.

Removable Garmin Nuvi mount sized to sit over the factory navigation display. A raised upper lip locates it in the recess

Holder that keeps a second-row seat-belt buckle upright so children can buckle themselves more easily. Designed around the Discovery mid-row seat geometry.

Replacement centre cap for a Discovery 3 alloy wheel. Confirm wheel and bore dimensions against the original before printing.

Replacement adjuster for the rear seat. Includes the original version and a revised version that prints without supports

Replacement toggle that retains the rear towing-connection flap. Print at 100% infill

Replacement quarter-turn screw for retaining the rear-bumper towbar access door when the towbar is not fitted. Print with high infill and confirm engagement before road use.

Two-part eyelet mount that clamps around a factory roof rail using common M8 hardware. The source recommends PETG, 20% infill, doubled infill lines, and three walls. Use only for light-duty restraint and never as a rated recovery or lifting point.

Insert for the centre-console cubby refrigerator in a 2007 Discovery 3, designed to keep drink cans from rolling and vibrating while driving. Use a cabin-temperature-resistant material.

Dashboard phone mount for fitting a Quad Lock interface in the Discovery 3/LR3 cabin. Confirm the mating interface and dashboard fit before final installation.

Dashboard bracket for a 9.3-inch portable CarPlay display. The upper edge tucks beneath the dashboard trim while taped feet support the screen

Replacement air intake for a Webasto Thermo Top V fuel-burning heater when the original retaining legs have broken. Print with the legs downward and supports from the build plate.

Wheel-centre reference tool that holds a tape measure at the true hub centre during suspension-height calibration.

Replacement receiver that grips the quarter-turn plastic screw securing the rear tow-bar cover.

Two-part centre-console organiser comprising a main tray and removable divider. Use a cabin-temperature-resistant material because PLA may soften in summer heat.

Push-fit cap for covering an unused roof-rack mounting hole.

Replacement plunger for a broken fuel-filler-door actuator.